徐州附近想过夜电话联系

Welcome to Shanghai liefan doors and windows official website
Standard Specification for installation of aluminum alloy doors and windows
Editor: liefan, October 29, 2019 10:00:01

Specification for installation of aluminum alloy doors and windows

The process standard is applicable to the installation of aluminum alloy doors and windows in residential buildings.

2. Standard construction preparation for installation of aluminum alloy doors and windows

2.1 materials and main machines and tools

2.1.1 the thickness, specification and model of aluminum alloy door and window profile shall meet the design requirements and shall be provided with factory certificate.

2.1.2 the hardware fittings used for aluminum alloy doors and windows shall match the model of doors and windows. Stainless steel parts and other parts must be treated with anti-corrosion.

2.1.3 the anti-corrosion materials and thermal insulation materials shall meet the requirements of the drawings and shall have the factory certificate.

2.1.4 the medium cement sand of No.325 or above shall be prepared as required. Chongqing is a super fine sand area, and small-sized fishstone can be added to the fine sand in proportion.

2.1.5 the connecting iron feet and plates fixed to the structure shall be prepared according to the specifications required in the drawings. And do a good job in anti-corrosion treatment.

2.1.6 the specification and model of the welding rod shall be consistent with the welding parts, and the factory certificate shall be provided.

2.1.7 the variety and model of caulking material and sealing paste shall meet the design requirements.

2.1.8 anti rust paint, iron yarn or aluminum yarn, yarn pressing bar, etc. shall meet the design requirements and have the factory certificate.

2.1.9 the specification and model of the sealing strip shall meet the design requirements, and the adhesive shall match the material of the sealing strip and have the factory certificate of the product.

2.1.10 main machines and tools are aluminum alloy cutting machine, electric hand drill, round file, semicircular file, cross screw driver, scriber, iron foot, compass, steel ruler, steel ruler, steel ruler, drill, hammer, spade, trowel, bucket, water brush, electric welding machine, welding rod wire, mask, welding rod, etc. 2.2 operation conditions 2.2.1 the structure quality reaches the qualified standard after acceptance, and the handover procedures are handled between the types of work.

2.2.2 snap the window center line and horizontal line of 10.5cm according to the size shown in the figure. The in and out line from the window to the external wall is called three line control of the external wall doors and windows, so as to correct whether the size and elevation of the door and window openings meet the requirements of the design drawings. If there is any problem, it should be chiseled in advance.

2.2.3 check whether the position of connecting iron feet on both sides of aluminum alloy doors and windows is consistent with the position of reserved holes on the wall. If there are problems, deal with them in advance and clean up the impurities in the reserved holes. Project training needs analysis research report development trend work plan sales strategy assessment system management manual solution assessment management cost management staff manual research report development analysis report operation analysis operation instruction marketing planning report management control system scheme effectiveness questionnaire assessment evaluation plan template

2.2.4 for unpacking inspection of aluminum alloy doors and windows, remove the wrapping cloth around the window frame, check the model according to the drawing requirements, and check the appearance quality and surface flatness. If there are any defects such as wedge, angle shifting and warping, serious exceeding the standard, serious damage, large color difference, etc., the relevant personnel shall be consulted to solve the problem, and the installation can be carried out after the repair and identification is qualified. 2.2.5 carefully check the integrity of the protective film of aluminum alloy doors and windows. If there is any damage, it should be repaired and then installed.

3. Standard operation process for installation of aluminum alloy doors and windows

3.1 process flow line snapping to find out the rules of the above three lines → door and window hole treatment → embedding connecting iron parts in the door and window opening → unpacking and checking the aluminum alloy doors and windows → transporting them to the installation site according to the drawing number → checking the aluminum alloy protective film → installing the aluminum alloy doors and windows → caulking around the doors and windows, filling with thermal insulation materials → cleaning → installing hardware accessories → installing the door and window sealing strip → Quality inspection → yarn fan installation.

There are also strict specifications for the size of the broken bridge aluminum alloy window   [ Back to home page ] [ Printing ] [ Back to previous page ]    Introduction of three types of sunshine houses

Hot Tags:

Product Center